Tesla Model 3: Compressor- Remove

Warning:

Only technicians who have been trained in High Voltage Awareness are permitted to perform this procedure. Proper personal protective equipment (PPE) and insulating HV gloves with a minimum rating of class 0 (1000V) must be worn at all times a high voltage cable, busbar, or fitting is handled. Refer to Tech Note TN-15-92-003, "High Voltage Awareness Care Points" for additional safety information.

Remove

1. Remove the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
2. Remove the outer HVAC plenum duct. See Duct - HVAC Plenum - Outer (Remove and Replace).
3. Recover the A/C refrigerant. See A/C Refrigerant (Recovery and Recharge).

Note: Recover the refrigerant while continuing this procedure.

4. Disconnect 12V power. See 12V Power (Disconnect and Connect).
5. Perform the vehicle electrical isolation procedure. See Vehicle Electrical Isolation Procedure.
6. Remove the penthouse HV cap. See Cap - Penthouse HV (Remove and Replace).
7. Remove the LH 2nd row seat side bolster. See Bolster - Side - Seat - 2nd Row - LH (Remove and Replace).
8. Remove the LH rear sill panel trim. See Trim - Sill Panel - Rear - LH (Remove and Replace).

9. Release the clips that attach the low voltage electrical harness to the charge port to HV battery harness bracket at the penthouse.

10. Remove the bolts that attach the charge port to HV battery harness bracket at the penthouse, and then remove the bracket from the vehicle.

11. Release the clip that attaches the charge port electrical harness to the vehicle.

12. Slide the security tab to the unlock position, release the locking handle, and then disconnect the charge port electrical harness from the penthouse DC input connector.
13. Remove the front aero shield. See Panel - Aero Shield - Front (Remove and Replace).

14. Disconnect the compressor HV electrical connector from the HV electrical harness.

15. Release the clips that attach the compressor HV electrical harness to the bulkhead.

16. Disconnect the electrical harness from the high pressure transducer connector.
17. Lower the vehicle.

18. Disconnect the low voltage electrical connector from the compressor.

19. Remove the bolt that attaches the ground harness to the compressor. Torque 6 Nm

20. Release the clips that attach the low voltage electrical harness to the compressor and compressor bracket.

21. Remove the bolt that attaches the suction/liquid line bracket to the shock tower brace, and then separate the bracket from the brace.

22. Disconnect the electrical harness from the low pressure transducer connector.

Note: Make sure that the refrigerant has fully recovered before continuing this procedure.

1. Remove the bolt that attaches the suction/liquid line to the chiller and EXV assembly, and then remove the line from the chiller and EXV assembly.
2. Remove and discard the o-rings from the suction/liquid line fitting.

3. Release the clip that attaches the electrical harness to the suction liquid line.

4. Disconnect the electrical harness from the powertrain coolant pump connector.

5. Release the clip that attaches the suction/liquid lines to the superbottle.

6. Remove the nut that attaches the discharge line to the compressor, and then remove the discharge line from the compressor.
7. Remove and discard the o-ring from the discharge line.

8. Remove the nut that attaches the suction/liquid line to the compressor, and then remove the suction/liquid line from the compressor.
9. Remove and discard the o-ring from the suction/liquid line.

10. Release the clip that attaches the compressor HV electrical harness to the crossbeam.
11. Move the compressor HV electrical harness forward of the shock tower brace to ease compressor removal.

12. Remove the bolts that attach the compressor to the shock tower brace, and then lower the compressor and remove it from the vehicle.

Caution:

Set the compressor so that the refrigerant fittings are up, and oil will not leak from them. Before the replacement compressor can be installed, the removed compressor and the oil inside must be weighed.

13. Release the clip that attaches the compressor HV electrical harness to the intermediate bracket.

14. Remove the bolts that attach the intermediate bracket to the compressor, and then remove the bracket from the compressor.

15. Release the clips that attach the acoustic cover over to the compressor, and then remove the acoustic cover.
16. Use a digital scale to weigh the removed compressor and record its weight.

Note: Do not drain any oil from the removed compressor.

READ NEXT: