Tesla Model 3 Owners & Service Manuals

Tesla Model 3: Panel - Door Trim - Front - LH (Remove and Replace) - Install

Install

  1. Inspect the condition of the LH front door and the LH front door trim panel. Replace any broken clips and repair any damage.
  2. Bring the trim panel to the door, and rest it on the door edge.

Panel - Door Trim - Front - LH (Remove and Replace)- Install

  1. If present, remove and discard the highlighted clip.

Panel - Door Trim - Front - LH (Remove and Replace)- Install

  1. Route the harness as illustrated, making sure to attach the harness to the hooks on the door trim panel.
  2. Fasten the clips that attach the electrical harnesses to the trim panel.
  3. Connect the electrical harness to the LH front door trim panel connectors.

Panel - Door Trim - Front - LH (Remove and Replace)- Install

  1. Position the manual release cable in a vertical orientation, and slide the cable barrel end into the release lever.

Panel - Door Trim - Front - LH (Remove and Replace)- Install

  1. Pivot the manual release cable collar to a horizontal orientation, and press the collar into the trim panel.

Note: Make sure the manual release cable is routed underneath the door harness.

Panel - Door Trim - Front - LH (Remove and Replace)- Install

  1. Lift the trim panel, compress the LH front door inner belt seal slightly, and then hook the three trim panel tabs into the top edge of the door.
  2. Move the electrical harness connector for the puddle lamp out the hole in the bottom of the trim panel.
  3. Install the LH front door puddle lamp. See Puddle Light - Front Door - LH (Remove and Replace).
  4. Make sure that the puddle lamp and map pocket ambient light illuminate when connected.
  5. Fasten the clips that attach the trim panel to the door.
  6. Make sure that the trim panel fits tightly, and that there are no gaps from misaligned or bent clips.

Rear
Rear

Panel - Door Trim - Front - LH (Remove and Replace)- Install

Middle
Middle

  1. Install the screws that attach the trim panel to the door. Torque 6 Nm

Caution:

Make sure that all fasteners are properly torqued and not cross-threaded.

Front
Front

  1. Install the reflector to the rear edge of the trim panel and the screw cover to the front of the armrest.
  2. Install the front LH door tweeter. See Tweeter - Front Door - LH (Remove and Replace).
  3. Close the door and verify the operation of the manual door release lever, that the door latch releases smoothly and easily.
  4. Raise the window and close the door.

    READ NEXT:

     Panel - Door Trim - Rear - LH (Remove and Install)

     Panel - Door Trim - Rear - LH (Remove and Install) - Remove

    Remove Open the LH rear door, and fully lower the window. Remove the LH rear door puddle light. See Puddle Light - Rear Door - LH (Remove and Replace). Release the clip that attaches

     Panel - Door Trim - Rear - LH (Remove and Install) - Install

    Install Inspect the condition of the LH rear door and the LH rear door trim panel. Replace any broken clips and repair any damage. Bring the trim panel to the door, and rest it on the door edge.

    SEE MORE:

     Trim - B-Pillar - Lower - LH (Remove and Replace)

    Remove Remove the LH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace). Remove the LH middle A-pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace). Remove the LH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace). Rem

     Controller - High Voltage- Remove

    Warning: Only technicians who have been trained in High Voltage Awareness are permitted to perform this procedure. Proper personal protective equipment (PPE) and insulating HV gloves with a minimum rating of class 0 (1000V) must be worn at all times a high voltage cable, busbar, or fitting is

    © 2019-2024 Copyright www.tmodel3.com