Tesla Model 3 Owners & Service Manuals

Tesla Model 3: Module - Body Controller - Front (RWD) - Install

Install

  1. Set the front body controller module where it installs into the vehicle, and then tilt the module forward

Module - Body Controller - Front (RWD)-Install

  1. Install the ground strap to the lower rear of the front body controller module, and then install the bolt that attaches the ground strap to the module.  Torque 9 Nm

Module - Body Controller - Front (RWD)-Install

  1. Install the ground strap to the lower right side of the front body controller module, and then install the bolt that attaches the ground strap to the module. Torque 9 Nm

Module - Body Controller - Front (RWD)-Install

  1. Install the ground strap to the upper rear of the front body controller module, and then install the bolt that attaches the ground strap to the module.  Torque 9 Nm

Module - Body Controller - Front (RWD)-Install

  1. Slide the busbar onto the lower stud, and then fasten the electrical harness clips (x2) to the bottom of the front body controller module.

Module - Body Controller - Front (RWD)-Install

  1. Install the bolts (x3) that attach the front body controller module to the body. Torque 10 Nm Torque 10 Nm

Module - Body Controller - Front (RWD)-Install

  1. Install new nuts (x6) and new bolt to attach the power and ground cables to the front body controller module. Torque 8.5 Nm Torque 8.5 Nm

Note: Make sure that the terminal lugs fit in their channels neatly

Module - Body Controller - Front (RWD)-Install

  1. Connect the electrical harness to the front body controller module connectors (x4).

Module - Body Controller - Front (RWD)-Install

  1. Visually inspect that the power and the ground cables exit the front body controller module neatly in their respective channels, and parallel to each other.

Caution:

Make sure that no cables or wires will be pinched when the front body controller module cover is installed.

Module - Body Controller - Front (RWD)-Install

Module - Body Controller - Front (RWD)-Install

  1. Install the front body controller module cover to the front body controller module, and then install the bolts (x9) that attach the cover to the module.  Torque 6 Nm

Module - Body Controller - Front (RWD)-Install

  1. Connect the thermal harness to the front body controller module connector.

Module - Body Controller - Front (RWD)-Install

  1. Fasten the clip that attaches the suction/liquid lines to the body near the TXV.

Module - Body Controller - Front (RWD)-Install

  1. Install the thermal harness cover to the front body controller module, and then install the bolt that attaches the cover to the module.  Torque 6 Nm
  2. Install the 12V battery bracket. See Bracket - 12V Battery (RWD) (Remove and Replace).
  3. Install the 12V auxiliary battery. See Battery - 12V (Remove and Replace).
  4. Install the 12V battery strap. See Strap - 12V Battery (Remove and Replace).
  5. Connect 12V power. See 12V Power (Disconnect and Connect).
  6. Connect a laptop with Toolbox to the vehicle.
  7. Use Toolbox to update the vehicle firmware.
  8. In Toolbox, click the play button next to the "TESTRESET_ VCFRONT" and select Run,
  9. Disconnect the laptop from the vehicle.
  10. Install the cowl screen panel. See Panel - Cowl Screen (Remove and Replace).
  11. Install the LH and RH wiper arms. See Wiper Arms (Remove and Replace).
  12. Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  13. Install the hood latch cover. See Cover - Hood Latch (Remove and Replace).
  14. Install the cabin intake duct. See Duct - Cabin Intake (Remove and Replace).
  15. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  16. Install the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).

    READ NEXT:

     Module - Body Controller - LH (Remove and Replace)

     Module - Body Controller - LH - Remove

    Remove Remove the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace). Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace). Disco

     Module - Body Controller - LH - Install

    Install Install the clip that attach the shroud to the LH body controller module. Note: Make sure that both clips are fully seated so that the edge of the shroud is parallel with the line on the b

    SEE MORE:

     Check Base - Sun Visor - Driver (Remove and Replace)

    Remove Remove the LH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace). Release the clips that attach the LH air wave end cap to the main instrument panel decor trim, and then remove the cap from the vehicle. Install Installation procedure is the rev

     Remove Dirt Inclusion

    Apply isopropyl alcohol to the general area of the defect, and then wipe the area with a clean microfiber towel. While wearing a nitrile glove, run hand over the area around the dirt inclusion and check for fine bumps in the paint. If bumps are detected, perform clay treatment on the

    © 2019-2024 Copyright www.tmodel3.com