Tesla Model 3 Owners & Service Manuals

Tesla Model 3: Hub - Front - LH (Dual Motor) - Remove

Tesla Model 3 2017-2025 Service Manual / Suspension / Front Suspension (Including Hubs) / Hub - Front - LH (Dual Motor) (Remove and Replace) / Hub - Front - LH (Dual Motor) - Remove

Hub - Front - LH (Dual Motor) (Remove and Replace)

SPECIAL TOOLS

Card, Magnetic Field Viewer (1062500-00-A)

Remove

  1. If equipped, remove the LH front wheel center cap. See Cap - Wheel (Remove and Replace).
  2. Loosen the LH front wheel lug nuts.

Caution:

Use only hand tools to remove or install the fasteners. Do not use impact or power tools.

Caution:

Use a 6 point socket. Do not use a 12 point socket or a specialty socket.

Hub - Front - LH (Dual Motor) - Remove

  1. Loosen the LH front drive unit halfshaft nut.
  2. Raise and support the vehicle. See Raise Vehicle - 2 Post Lift.
  3. Remove the LH front wheel. See Wheel (Remove and Install)

Hub - Front - LH (Dual Motor) - Remove

  1. Remove and discard the LH front drive unit halfshaft nut and washers.

Note: The washers are attached to the nut.

  1. Position the hub puller tool onto the LH front wheel studs, and then hand tighten the wheel lug nuts (x5)
  2. Remove the LH front drive unit halfshaft from the LH front hub assembly

Note: While holding the hub in position, turn the hydraulic hub puller tool handle clockwise to separate the LH front drive unit halfshaft from the hub assembly.

  1. Remove the hub puller tool from the LH front wheel studs.

Hub - Front - LH (Dual Motor) - Remove

  1. Remove the bolt that attaches the front brake hose bracket to the LH front knuckle.

Hub - Front - LH (Dual Motor) - Remove

  1. Remove and discard the bolts that attach the LH front brake caliper to the LH front knuckle, and then hang the caliper aside with an S-hook.

Hub - Front - LH (Dual Motor) - Remove

  1. Remove the LH front rotor from the vehicle.

Hub - Front - LH (Dual Motor) - Remove

  1. Remove the bolts that attach the LH front hub to the LH front knuckle.
  2. Remove the LH front hub from the vehicle

    READ NEXT:

     Hub - Front - LH (Dual Motor) - Install

    Install Use a magnetic field viewing card to check the LH front hub's tone ring. Line up the LH front drive unit halfshaft splines, and then install the LH front hub on the LH front knuckle.

     Hub - Front - LH (RWD) (Remove and Replace)

    SPECIAL TOOLS Card, Magnetic Field Viewer (1062500-00-A) S-Hook (10821717-00-A) Remove Remove LH front wheel. See Wheel (Remove and Install). Remove the LH front brake rotor. See Brake Rotor -

     Knuckle - Suspension - Front - LH (Dual Motor) (Remove and Replace)

    SEE MORE:

     Harness - Instrument Panel (Remove and Replace)

    Remove Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace). Remove the cabin intake duct. See Duct - Cabin Intake (Remove and Replace). Remove the hood latch cover. See Cover - Hood Latch (Remove and Replace). Remove the underhood storage unit carpet. See Ca

     Automatic Emergency Braking

    The forward looking camera(s) and the radar sensor are designed to determine the distance from a detected object traveling in front of Model 3. When a frontal collision is considered unavoidable, Automatic Emergency Braking is designed to apply the brakes to reduce the severity of the impact.

    © 2019-2025 Copyright www.tmodel3.com