Tesla Model 3 Owners & Service Manuals

Tesla Model 3: Headlights - Adjust - EMEA (Wall Method)

Tesla Model 3 2017-2025 Service Manual / Electrical / Exterior Lights / Headlights - Adjust - EMEA (Wall Method)

Headlights - Adjust - EMEA (Wall Method)

Adjust Headlights Using a Wall

Apply Tape to Wall
Apply Tape to Wall

  1. Apply tape to a wall 23.6 in (60 cm) from the ground.
  2. Apply tape to the floor 31.1 ft (9.5 m) from the wall.

Note: EU vehicles require a 1 to 1.5 degree downward inclination in the headlight beam. For example, a vehicle parked 10 m from the wall would have 10 cm beam drop, from 70 cm height at the lens to 60 cm height at the wall.

Apply Tape to Floor and Align Front Fascia
Apply Tape to Floor and Align Front Fascia

  1. Park the vehicle on a flat surface perpendicular to a wall, aligning the front fascia with the tape on the floor.
  2. Make sure that all 4 tires are inflated to specification.
  3. Use a laser measure to make sure the vehicle is positioned perpendicular to the wall. Measure the distance from the center of both front wheels to the wall. Both measururements from the center of the wheels to the wall should be equal. If the measurements are unequal, re-position vehicle accordingly.

Alignment Targets
Alignment Targets

  1. Use a laser measure to determine the center point of the vehicle. Hold the laser measure perpendicular to the wall and project the laser onto the center point of the vehicle. Mark the center line on the wall with a piece of tape.

Measure 72 cm from Center
Measure 72 cm from Center

  1. Measure 28 in (72 cm) horizontally on either side of the center line, and then mark these measurements with a piece of tape.

Create Alignment Targets
Create Alignment Targets

  1. Add a vertical strip of tape to both marks made in the step above to make targets for the horizontal headlight alignment.
  2. Open the front LH door.
  3. Place weight in the driver's seat equal to approximately 75 kg.
  4. On the vehicle touchscreen, enter headlight adjustment mode: Controls > Service > Adjust Headlights.

Cover the Right Headlight
Cover the Right Headlight

  1. Use a shop towel to completely cover the RH headlight.
  2. On the vehicle touch screen, select Left.

Adjust the Left Headlight Beam
Adjust the Left Headlight Beam

  1. On the steering wheel, use the left scroll wheel to adjust the beam level. Adjust the LH headlight so that the top right part of the beam aligns with the tape mark on the wall, and the angled portions align as shown.
  2. When LH headlight adjustment is complete, uncover the RH headlight.

Cover the Left Headlight
Cover the Left Headlight

  1. Use a shop towel to completely cover the LH headlight.
  2. On the vehicle touch screen, select Right.

Adjust the Right Headlight Beam
Adjust the Right Headlight Beam

  1. On the steering wheel, use the right scroll wheel to adjust the beam level. Adjust the RH headlight so that the top right part of the beam aligns with the tape mark on the wall, and the angled portions align as shown.
  2. When RH headlight adjustment is complete, uncover the LH headlight.
  3. Exit headlight adjustment mode from the vehicle center display.
  4. Remove the weight from the driver's seat.
  5. Close the front LH door.

    READ NEXT:

     Headlights - Adjust - NA (Tool Method)

    Adjust Headlights Using a Headlight Tester Park the vehicle on a level surface. Make sure that all 4 tires are inflated to specification. Open the front trunk hood. On the touchscreen, enter h

     Headlights - Adjust - NA (Wall Method)

    Adjust Headlights Using a Wall Position the vehicle for adjusting the headlights. The vehicle should be: Located in a darkened area. Parked on a level surface. Perpendicular to a wall that ha

     Headlight - LH (Remove and Replace)

    Headlight - LH- Remove It is recommended that the vehicle be powered down before executing headlight replacement to ensure that the new headlights are recognized during vehicle firmware update. Re

    SEE MORE:

     End Panel - Center Console (Remove and Replace)

    Remove Remove the center console lower rear panel. See Panel - Lower Rear - Center Console (Remove and Replace). Remove the center console air vent panel. See Panel - Air Vent - Center Console (Remove and Replace). Remove the bolts (x2) and release the clips (x6) that attach the center

     Controller - High Voltage (Remove and Replace)

    Controller - High Voltage- Remove Warning: Only technicians who have been trained in High Voltage Awareness are permitted to perform this procedure. Proper personal protective equipment (PPE) and insulating HV gloves with a minimum rating of class 0 (1000V) must be worn at all times a high volt

    © 2019-2025 Copyright www.tmodel3.com