Tesla Model 3: Harness - Main Front- Install

Install

1. Install the electrical harness into the vehicle.
2. Route the RH side of the electrical harness from the front body controller module area, through the underhood storage unit area, and to the RH wheel liner.
3. Route the LH side of the electrical harness from the front body controller module area, through the underhood storage unit area, and to the LH wheel liner.

4. Fasten the clips that attach the electrical harness to the body in the LH frame rail area.

5. Connect the electrical harness to the connectors in the bulkhead area.

6. Fasten the clips that attach the electrical harness to the body in the bulkhead area.

7. Fasten the clips that attach the electrical harness to the body in the front RH frame area.
8. Raise the vehicle.

9. Connect the electrical harness to the front LH side repeater lamp connector.

10. Fasten the clips that attach the electrical harness to the body in the front LH wheel area.

11. Connect the electrical harness to the connectors at the front of the front LH wheel liner area.

12. Fasten the clips that attach the electrical harness to the body at the front LH wheel liner area.

13. Connect the electrical harness to the front end module connector.

14. Connect the electrical harness to the connectors in the front LH fascia area.

15. Connect the electrical harness to the front RH side repeater lamp connector.

16. Fasten the clips that attach the electrical harness to the body at the rear of the front RH wheel liner area.

17. Connect the electrical harness to the connector at the front of the front RH wheel liner area.

18. Fasten the clips that attach the electrical harness to the body at the front of the front RH wheel liner area.

19. Connect the electrical harness to the connectors in the front RH fascia area.
20. Install the front LH and front RH arch liners. See Wheel Arch Liner - Front - LH (Remove and Replace).
21. Install the front LH and front RH wheels. See Wheel (Remove and Install).
22. With an assistant, move the vehicle from the lift.

Caution:

The vehicle is safely pushed for only a very short distance and at a very slow speed.

23. Place wheel chocks on both rear wheels.
24. Open the front LH and front RH doors.

25. Connect the electrical harness to the RH headlight connector.

26. Fasten the clips that attach the electrical harness to the body in the RH headlight area.

27. Install a new bolt to attach the electrical harness ground terminal to the body in the front RH frame rail area. Torque 8 Nm

28. Fasten the clips that attach the electrical harness to the body in the front RH frame rail area.

29. Install the bolt that attaches the electrical harness ground terminal to the body in the TXV area Torque 9 Nm

30. Connect the electrical harness to the TXV connector.

31. Fasten the clips that attach the electrical harness to the body in the HVAC plenum duct area.

32. Connect the electrical harness to the LH headlight connector.

33. Connect the electrical harness to the steering rack connectors and the connectors in the front LH frame rail area.

34. Install new bolts (x4) to attach the electrical harness ground terminals to the body in the front LH frame rail area. Torque 8 Nm

35. Fasten the clips that attach the electrical harness to the body in the front LH frame rail area.

36. Connect the electrical harness to the ABS unit connector.

37. Connect the electrical harness to the brake booster connector.

38. Connect the electrical harness to the connectors (x3) in the brake booster area.

39. Fasten the clip that attaches the electrical harness to the body in the brake booster area.
40. Move the LH side of the electrical harness in through the bulkhead.

41. Connect the electrical harness to the LH body controller module connector.

42. Connect the inline electrical harness connector X909, and then attach it to the LH body controller module.

43. Install the power cable of the electrical harness to the LH body controller module, and then install a new nut to attach the power cable to the module. Torque 8.5 Nm
44. Move the RH side of the electrical harness in through the bulkhead.

45. Connect the electrical harness to the car computer connectors (x7).

46. Fasten the clips that attach the electrical harness to the car computer.

47. Connect the inline electrical harness connector, and then attach it to the RH body controller module.

48. Raise the RH body controller module into position, and install a new nut to attach the module to the A-pillar. Torque 6 Nm

49. Install the power cables of the electrical harness to the RH body controller module, and then install the new nuts (x2) to attach the power cables to the module. Torque 8.5 Nm

50. Connect the electrical harness to the RH body controller module connector.

51. Install the HVAC plenum inner duct to the body, and then install the fasteners that attach the inner duct to the body.

52. Install the HVAC plenum outer duct onto the HVAC plenum inner duct, and then fasten the clips that attach the outer duct to the inner duct.
53. Install the 12V battery bracket. See Bracket - 12V Battery (RWD) (Remove and Replace).

54. Install the front body controller module to the body, and then install the bolt that attaches the ground strap to the lower rear of the module. Torque 9 Nm

55. Install the ground strap to the lower right side of the front body controller module, and then install the bolt that attaches the ground strap to the module Torque 9 Nm

56. Install the ground strap to the upper rear of the front body controller module, and then install the bolt that attaches the ground strap to the module. Torque 9 Nm

57. Install the lower busbar onto the stud, and then fasten the clips that attach the bottom of the front body controller module to the body.

58. Install the bolts that attach the front body controller module to the body. Torque 10 Nm Torque 10 Nm

59. Install new nuts (x6) and new bolt to attach the power and ground cables to the front body controller module. Torque 8.5 Nm Torque 8.5 Nm

Note: Make sure that the terminal lugs fit in their channels neatly.

60. Connect the main front harness to the front body controller module connectors.

61. Visually inspect that the power and the ground cables exit the front body controller module neatly in their respective channels, and parallel to each other.

Caution:  Make sure that no cables or wires will be pinched when the front body controller module cover is installed.

62. Install the front body controller module cover to the front body controller module, and then install the bolts that attach the cover to the module. Torque 6 Nm

63. Fasten the clip that attaches the suction/liquid lines to the body near the TXV.

64. Connect the thermal harness to the front body controller module connector.

65. Install the thermal harness cover to the front body controller module, and then install the bolt that attaches the cover to the module. Torque 6 Nm
66. Install the wiper motor assembly. See Wiper Motor (Remove and Replace).
67. Install the nut that attaches the 12V battery rear hook tie down.
68. Install the 12V auxiliary battery. SeeBattery - 12V (Remove and Replace).
69. Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
70. Install the RH air wave duct. See Duct - Air Wave - RH (Remove and Replace).
71. Install the RH footwell duct. See Duct - Footwell - RH (Remove and Replace).
72. Install the glove box. See Glove Box (LHD) (Remove and Replace).
73. Install the main instrument panel decor. See Decor Trim - Instrument Panel - Main (Remove and Replace).
74. Install the front passenger knee airbag. See Airbag - Knee - Front Passenger (Remove and Replace)
75. Install the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
76. Fasten the clips that attach the footrest.
77. Install the driver knee airbag. See Airbag - Knee - Driver (Remove and Install).
78. Install the LH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
79. Connect 12V power. See 12V Power (Disconnect and Connect).
80. Remove the wheel chocks.
81. Close the hood.
82. Close the front LH and front RH doors.

READ NEXT: