Tesla Model 3 Owners & Service Manuals

Tesla Model 3: Platter Enclosure Air Leak Test

Tesla Model 3 2017-2025 Service Manual / Battery System / HV Battery Enclosure / Platter Enclosure Air Leak Test

DRAFT

Warning:

This procedure was derived from pre-production computer models, and might not reflect the real-world situation. Warnings and cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components.

SPECIAL TOOLS

Pack Enclosure Leak Tester, HV Battery (1026636-00-A)

Pack Kit, Enclosure, Leak Test, HV Battery, Complete (1140501-00-A)

Kit, Encl Leak Test Adapters, HV Battery (1144879-00-A)

Parent topic: 1610 - HV Battery Enclosure

Procedure

  1. Remove the mid aero shield panel. See Panel - Aero Shield - Mid (Remove and Replace).

Platter Enclosure Air Leak Test

  1. Remove and discard the breather from the RH HV battery vent shroud assembly.

Platter Enclosure Air Leak Test

  1. Install the leak test adapter plug into the RH shroud assembly.

Platter Enclosure Air Leak Test

  1. Remove and discard the breather from the LH HV battery vent shroud assembly.

Platter Enclosure Air Leak Test

  1. Install the leak test adapter into the LH shroud assembly.
  2. Connect the pack enclosure leak tester to the leak test adapter in the LH HV battery shroud assembly.
  3. Close both valves on the pack enclosure leak tester, and then connect a compressed air supply line.
  4. Fully close the regulator, and then open the inlet valve.
  5. Set the regulator to 0.15 psi.
  6. Open the outlet valve, and allow at least 45 seconds for the pressure to stabilize to 0.15 psi.
  7. Close the inlet valve, record the starting pressure displayed, and then start a 60-second timer.
  8. After 60 seconds record the ending pressure displayed.
  9. Subtract the ending pressure from the starting pressure, and if:
  • The difference is greater than 0.0054 psi, check the hose, adapter, and plug fittings, close the outlet valve and open the inlet valve, check the regulator pressure, and then retest from step 10. If the difference is still greater than 0.0054 psi, escalate a Toolbox session.
  • The difference is 0.0054 psi or less, continue the procedure.
  1. Disconnect the air supply from the pack enclosure leak tester.
  2. Open the inlet valve, and then disconnect the pack enclosure leak tester from the leak test adapter in the LH HV battery shroud assembly.
  3. Remove the leak test adapter from the LH HV battery shroud assembly, and then install a new breather into the LH shroud assembly.
  4. Remove the leak test adapter plug from the RH HV battery shroud assembly, and then install a new breather into the RH shroud assembly.
  5. Install the mid aero shield panel. See Panel - Aero Shield - Mid (Remove and Replace).

    READ NEXT:

     Ski - Center Rail - HV Battery (RWD) (Remove and Replace)

    Ski - Center Rail - HV Battery (RWD) - Remove SPECIAL TOOLS Lever Lock, HV Connector, Model 3 (1140311-00-A) Warning: Only technicians who have been trained in High Voltage Awareness are permitted

    SEE MORE:

     Duct - Air Wave - LH (Remove and Replace)

    Remove Remove the IP carrier. See IP Carrier (Remove and Replace). Remove the screws (x2) that attach the LH air wave duct to the cross bar beam, and then remove the duct from the vehicle. Install Install the LH air wave duct to the cross car beam, and then install the screws (x

     Harness - Main Front (Remove and Replace)

    Harness - Main Front- Remove Remove Open the front LH and front RH doors Open the hood. Place wheel chocks on both rear wheels. Put vehicle in Neutral. Disconnect 12V power. See 12V Power (Disconnect and Connect). Remove the LH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove

    © 2019-2025 Copyright www.tmodel3.com