Tesla Model 3 Owners & Service Manuals

Tesla Model 3: Brake Hose - Flexible - Front - LH (Remove and Replace)

Tesla Model 3 2017-2025 Service Manual / Brakes / Brake Pipes and Hoses / Brake Hose - Flexible - Front - LH (Remove and Replace)

 Brake Hose - Flexible - Front - LH (Remove and Replace)

SPECIAL TOOLS

Brake Hose - Flexible - Front - LH (Remove and Replace)

Flare nut crowfoot set (1079041-00-A)

Remove

Caution: Brake fluid dissolves paint. Have clean towels and plenty of water standing by to wash spilled brake fluid off painted surfaces.

Note: Dispose of used brake fluid in a manner consistent with local environmental codes.

  1. Disconnect 12V power. See 12V Power (Disconnect and Connect).
  2. Remove the front LH wheel. See Wheel (Remove and Install).
  3. Position the oil drain under the front LH brake hose.

  Brake Hose - Flexible - Front - LH (Remove and Replace)

  1. Remove the brake line tube nut from the brake hose at the jounce hose bracket, and allow the fluid to drain.

  Brake Hose - Flexible - Front - LH (Remove and Replace)

  1. Release the clip that attaches the brake hose to the jounce hose bracket, and then remove the hose from the bracket.
  2. Position the oil drain under the brake caliper.

  Brake Hose - Flexible - Front - LH (Remove and Replace)

  1. Remove and discard the bolt and washers (x2) that attach the brake hose to the brake caliper, and allow the fluid to drain.

  Brake Hose - Flexible - Front - LH (Remove and Replace)

  1. Remove the bolt that attaches the brake hose bracket to the front LH knuckle, and then remove the hose from the vehicle.

Install

  Brake Hose - Flexible - Front - LH (Remove and Replace)

  1. Install the brake hose to the front LH knuckle, and then install the bolt that attaches the brake hose bracket to the knuckle. Torque 7 Nm

  Brake Hose - Flexible - Front - LH (Remove and Replace)

  1. Install a new bolt and washers (x2) to the brake hose.

  Brake Hose - Flexible - Front - LH (Remove and Replace)

  1. Install the brake hose to the brake caliper. Torque 42 Nm

  Brake Hose - Flexible - Front - LH (Remove and Replace)

  1. Install the brake hose into the jounce hose bracket, and then fasten the clip that attaches the hose in the bracket.

  Brake Hose - Flexible - Front - LH (Remove and Replace)

  1. Insert the brake line into the brake hose at the jounce hose bracket, and then use a crowfoot extension to install the brake line tube nut into the brake hose. Torque 16 Nm
  2. Remove the oil drain from under the vehicle.
  3. Install the front LH wheel. See Wheel (Remove and Install).
  4. Connect 12V power. See 12V Power (Disconnect and Connect).
  5. Bleed the brake caliper for the brake hose that was serviced. See Brake Fluid Bleed - One Caliper.

    READ NEXT:

     Brake Hose - Flexible - Rear - LH (Remove and Replace)

      SPECIAL TOOLS Flare nut crowfoot set (1079041-00-A)

     Brake Lines - 4 Tube Bundle - ABS to Wheels (Remove and Replace)

     Brake Lines - 4 Tube Bundle - ABS to Wheels - Remove

      SPECIAL TOOLS  Flare nut crowfoot set (1079041-00-A) Disconnect 12V power. See 12V

    SEE MORE:

     Wiper Blades (Remove and Replace)

    Note:  This procedure was formulated using a release candidate or production model. Follow safety requirements and use extreme caution when working on or near high-voltage systems and components. Remove Use the center display to put the wipers in "Service Mode." Release the tab that

     Airbag - Front Passenger (Remove and Install)

    DRAFT Warning:  This procedure was derived from pre-production computer models, and might not reflect the real-world situation. Warnings and cautions might be missing. Follow safety requirements and use extreme caution when working on or near high voltage systems and components. Remove R

    © 2019-2025 Copyright www.tmodel3.com